Fly high PIG!

This mechanical toy is one of a kind. Instead of just the basic wheel and axle application, this toy uses strings to enable it to move its wings.

Mechenical Toys

This videos show different types of mechenical toys. These can be applied ino my project later on.

Catterpillar!!

This picture shows a unique mechenical toy. By actually moving the axle, you can actually make the catterpillar move!

Mechenical toys

This mechenical toy is moved by its gears. It is a simple example to show how gears work. To enable it to move, the wheels are rotated and thus creates a force to enable it to be moved. For this toy, it is built in such a way that it can move in different ways as its wheel has a paticular shape so as to synchronize with the other wheels.

Instructions to Build a Billy Cart

A billy cart is a four-wheeled platform that you can ride down hills.It is also some sort of a mechenical toy There is a pad for sitting on and you steer it with your feet. I think it must be instinctive for kids to make billy carts because all kids seem to be able to build them without instruction.

What You Will Need

• three metres of building lumber (say, 50 X 75 millimetres (mm))
  


• a piece of 18 mm plywood about 400 X 350 mm
  


• a handful of 40 mm flat-head nails
  


• a handful of 80 mm flat-head nails
  


• four old, working ball bearings approximately 50 mm (or greater) diameter. You should be able to get these from a car wreckers or a mechanic.
  


• one 120mm long, 9mm thick bolt, with two nuts, two washers and an extra large diameter washer.
  
  The figure below shows how the frame of the billy cart is assembled. The dimensions are a rough guide only. The long piece should be sized so that whoever is going to ride the billy cart can sit on the seat and turn the front cross bar with his feet.

Start Building

• Cut the building lumber into nine pieces with the following lengths. Note that none of the dimensions are critical: cut to the nearest 10 mm. Cut one long piece of 1200 mm
  
• two cross pieces of 600 mm
  
• four wheel supports of 85 mm
  
• two seat supports of 70 mm
  
• Drill a 9mm hole through the centre of one of the cross pieces as shown in the figure. Be careful to drill the hole vertically through rather than at an angle.
  
• Drill a 9mm hole through the long piece at one end as shown in the figure. Make sure this hole is drilled vertically, too.
  
• Attach a ball bearing to a wheel support using the 40 mm nails. The ball bearing should protrude at least 10 or 15 mm below the bottom edge of the wheel support. And the outer ring of the ball bearing must not contact the wheel support or it will prevent the wheel from turning smoothly.

• Put four small flathead nails (or tacks) into the wood and underneath where the inner ring of the ball bearing will be. The nail heads should be just above the surface of the wood so that the ball bearing contacts only the nails heads and not the wood.
• Use six nails or so to hold the ball bearing. place the ball bearing against the support and hammer the nails in around the inner edge of the ball bearing. Make sure that the ball bearing is firmly secured; bend the nails outwards if needed. Attach the other three ball bearings to their wheel supports too.
  
• Nail the four wheel supports to the underside of the two cross pieces with three 80 mm nails.
  
• Nail the rear cross piece to the rear end of the long piece (that is, the end without the hole drilled in it) with two 80 mm nails. Make sure the cross piece is at right angles to the long piece. Also nail the seat supports to the cross piece. Put the nails through from the cross piece into the long piece.

• Nail the seat to the long piece and the supports with the 40 mm nails.
  Assemble the front cross piece to the long piece. Take the bolt and put a small washer on it, then the cross piece (push the bolt in from underneath), then put the large washer on, then the long piece then the small washer then the two nuts. Tighten the first nut by hand then screw the second nut down against the first and tighten them against each other with spanners.

The billy cart is complete! Sit on the seat and grip the seat with you hands. Steer with your feet on the front cross piece. Make sure that the long piece is the right length so that you can turn the front cross piece adequately. There is no brake but you can stop but putting the billy cart into a spin and making it skid sideways down the hill.

Hand Made lamps

These hand made lams are very expensive and one costs up to (S)$500! These lamps are carved from varnished teak wood and bamboo. Some of them have very sophisticated and complex designs while others have simple designs.

Different woods are the palette of the furnituremaker. They provide color and texture, strength and beauty to handmade furniture.

Each type of wood has characteristics to be considered when building a piece of furniture. Some are very hard and durable; some are flexible and suitable for bending. "Hardwood" is a term applied to trees that lose their leaves in winter. "Softwood" describes evergreens such as fir, pine and redwood. The actual durability a wood is described in a range from very soft to very hard.

Every wood has a distinctive grain structure. Woods such as white and red oak, ash and walnut have "open-pores". These woods have small holes in their surface that give the piece a textural quality. When a stain is applied to this type of surface, the stain tends to collect in the "open-pores" and appears darker than the rest of the piece. Tight grained woods include maple, alder, and cherry. These woods are smooth to the touch and can take finish evenly.

Introduction to the world of DnT

DnT: DEsign and Technology

In this world, Dnt can be found everywhere around you. Your computer, mobile phone, almost everything! In this blog, I will talk and dicover more about the world of DnT.